Category Archives: Family owned business

Water bore North Beach

George and the drilling team did a great job getting the drilling rig positioned at this job in North Beach.

The team drilled a 30 metre modern submersible water bore for this North Beach customer and got a plentiful supply of crystal clear water.

Difficult access on a sloping driveway drilling into a small walled garden bed. Way to go George!

All was tidied up and just the 100 mm bore casing left sticking out of the ground and a small pile of drilling waste sand on the verge.

Next we will cut down the bore casing to under the surface level and install the submersible pump.

If you have been at home and been thinking about a water bore, now is a great time. Call us on 9246 0111.

Water Bore Repair Floreat

This week our specialist bore electrician, Dave, called on a customer in Floreat reporting their submersible motor was tripping the circuit breaker in the meter box.

Dave found the one horsepower 2 wire submersible motor was not fused and the windings appeared intact but there was a complete dead short to earth.

garden bore Floreat
The retic controller turned on the 2 wire submersible bore via a 24v relay in this Floreat bore

At a minimum the submersible motor needed replacing but given the age of the unit it was decided to replace the wet-end (pump) as well and down hole electrical cable and stainless steel draw wire. Our submersible pump installer, Adam, will attend and install the new pump and motor and cables down the bore hole. There was no electrical junction box at the bore head so in this case Dave will return and one will be added for easier servicing in the future.

Dave  found the bore head under a hedge  near the letterbox.  nice detective work Dave!

submersible garden bore floreat
Well done Dave finding the submersible bore under that hedge,

It was great we were able to help with repair to this Floreat water bore so the garden would be ready for summer.

If you live in Floreat and need your water bore or reticulation repaired call us on 9246 0111 or enquire online HERE 

Burnt Capacitor in Bore Start Box

At this Ellenbrook job our specialist water bore electrician Dave found that the capacitor in the bore start box had ruptured. The client had called us on 9246 0111 when their water bore stopped working.

When our Ellenbrook client reported their bore wasn’t working we talked to them on the phone and asked a few questions to determine who was the best person to send.

As you will see pictured the start box cover was damaged by the burnt out capacitor. After we replaced the capacitor and start box we tested the motor electrically and all was OK. Our electrician carries a meggar tester specifically to send a signal down to the submersible pump motor and back up again to test it against known benchmarks.

Start Box has badly ruptured capacitor that needs replacing
Badly ruptured capacitor in submersible bore start box.

We have been in the bore drilling and repair business for nearly 20 years and will promptly diagnose bore faults and will repair in an economical and timely fashion. We carry the majority of spare bore and pump parts onboard.

Water bore and reticulation service
Water bore and retic service & repair

We provide a fast local bore and reticulation repair service to Ellenbrook, The Vines, Aveley, Brabham and all throughout the Swan Valley.

If you need your water bore or retic repaired call us on 9246 0111 or learn more HERE

Thanks for contacting us.

Swollen Bore Pipe

Our Perth northern suburbs bore service man snapped this pic of a swollen PVC pipe in Duncraig.

Heat induced swollen PVC pipe
Heat from a centrifugal pump that ran without water deformed this PVC pipe.

The centrifugal pump in an old well had clearly been run without water flowing. The pump had consequently overheated causing the heat stress on the adjacent PVC and the resultant swelling. If you have any bore or well problem in Perth then please call us. Our mobile service teams are ready to help you north or south of the river.

We have equipped bore service vans on the road who can help you with any issues you may have with your bore or reticulation we can fix it quickly.

If you are in the northern suburbs and your bore needs repairing call Troy on 9246 0111  or book a bore service online

Old Well New Submersible Pump

This old well in Myaree has had a carport built over the top. We are looking at converting it to a submersible pump which will be accessed by a hatch in the new liquid limestone floor. Call 9246 0111.

Replace Myaree well with old tin lid
Old style well in Myaree to be replaced

If have been in the business nearly 20 years and have extensive knowledge in Myaree and the surrounding areas of Melville and Booragoon.

If you live in the Myaree area and have an old well and would like to consider a modern submersible water bore call us on 9246 0111 or go to our website HERE

Joondalup Bore Service and Repair

Today our bore repair team attended a quite deep submersible bore just off Joondalup Drive after a call from a customer about a bore repair problem on 9246 0111.

Our specialist bore electrician tested the submersible pump motor from the surface at the control equipment and unfortunately it has tested both fused and down to earth.

bore controllers
3 phase DOL bore starter next to Single Phase bore start box

Another problem is no-one knows where the bore is located under the driveway. It is important for the home-owner to note the location of the bore when drilling a new bore or if buying a home with a bore. It saves money and time locating it.

We know the depth to water at this location is about 50 metres so the bore will be over 60 metres total depth.  We will need to winch it to the surface and confirm the tests. If necessary we will then replace the 3 phase motor. If we can confirm the motor is fused then our electrician will write it up as fused which may well be an “insured event” under the homeowners insurance policy.

Pump electrical faults should always be tested and recorded by a licensed electrician. Call us any time if you have any problem with your water bore or reticulation system in Joondalup or surrounds on 9246 0111.

We also drill new water bores and repair water bores in Joondalup and the surrounding suburbs of  Edgewater, Heathridge and Connolly. Check us out on our website HERE

Bore Repairs Claremont

We have just repaired a water bore in Claremont for an elderly client.

We talked to the customer on the phone and identified the fact we needed to send our specialist bore electrician, Dave. He found the submersible pump motor was not working and certified it as fused so the client could claim on her insurance. Her insurance policy covered pump motor fusion. It was quite deep for a Claremont bore so we had to winch the pump up over 30 metres.

We install and repair water bores in the Claremont area and surrounding suburbs of Nedlands and Dalkeith.

Call us anytime on 9246 0111 or book a bore service here 

 

D.O.L. bore starter
3 phase bore pump starter

Bore Air-Development?

We often get asked what it means to air develop a bore.  It is an important part of drilling a water bore in Perth suburbs.  Talk to us about it on 9246 0111.

Water bore Air-development.
Water gushes out of a new bore as compressed air is pumped down the borehole.

Ordinarily with a correctly constructed new water bore it is air-developed following drilling but before the installation of the submersible pump. This is particularly important in Perth’s typically sandy soils.

bore development
Water bore air development (credit : Lockyer Water)

Air development is a process where compressed air is pumped down the borehole both flushing out the drilling muds used to drill the bore and developing water flow from the aquifer. The accompanying diagram illustrates the results of development on a bore with a stainless steel screen. The principal is the same and equally important for those water bores constructed with slotted PVC screen. Slotted PVC screen is more common in Perth water bores.

Air-development is also used to clean out old and tired bores that have diminished water flows. It helps clear out years of silt etc and once again develops flow from the aquifer.

If your bore has reduced water flow call us for the solution on 9246 0111. Our mobile service teams operate Perth metro-wide. Also there is more information on air developing a water bore HERE

Submersible Bore Pump Shaft Broken

We had an unusual service call yesterday  (9246 0111) about a submersible bore pump that was producing only about 25% of the water that it normally delivered.

submersible pump shaft
Pump and motor uncoupled showing shaft.

We ruled out all the normal things like a hole in the poly rising main, pump wasn’t running backwards, none of the “normal” causes.???  When we winched the submersible pump to the surface we found the shaft joining the motor to the “wet-end” (pump) seemed OK but on uncoupling the submersible pump we noted inconsistencies. Found the shaft had sheared actually inside the pump leaving the first 4 of 12 impellers still turning. Quite an uncommon fault.

submersible pump
Submersible pump shaft snapped

Further detective work found the unusual auto start device had been turning the pump on/off, on/off incessantly contributing to the failure. Replaced the pump and installed it all back down the borehole with the original motor. Tested and all good now!

We have been in the water boring business for nearly 20 years and know how to repair and service water bores in Perth. We are a family business and will look after you.

Call us anytime on  9246  0111 or Troy on mobile 0408 454 130. Our mobile bore service teams visit all Perth suburbs.

There is more information on water bores in Perth HERE